ХАЛЛ ГРУПП · Equipment catalogue

Danfoss APP 8.2 / APP W 8.2 pumps

Axial-piston pump for reverse-osmosis systems. Parameters use the checked Danfoss 2024.06 data-sheet revision. Tabulated flow belongs to the stated speed and maximum table pressure, not any arbitrary duty point. Sound is measured on a motor-pump unit at maximum pressure and speed, at 1 m under EN ISO20361/EN ISO3744; it is not a noise guarantee for every installation. Pump, drive, coupling, filtration and supply scope are agreed separately.

Open selection and send an enquiry client@hallgroup.ru

Technical parameters

Technical source revision: AI274333290009en-000702 · 2024.06
Table fluid temperature: 2–50 °C; depends on NaCl
Table ambient temperature: 0–50 °C; see source qualification
Inlet filtration, section 9.1: 10 µm absolute; efficiency 99.98%; β10 ≥5000
Integrated flushing valve: Not available on APP(W)5.1–10.2
Inlet/outlet on sheet 29: M42 × 1.5; depth 13 mm
Bleed screw: M6; hex key 5 mm
DIN 6885 parallel key: 10 × 8 × 45 mm
Mounting flange on sheet 29: ISO 3019-2 125AHW
Dimension line 276 on sheet 29: 276 mm

Configurations and specifications

Configuration	Technical parameters	IMPA correspondence
APP 8.2 · 180B3008	Manufacturer article: 180B3008 Geometric displacement: 80.4 cm³/rev Minimum/maximum outlet pressure: 20 / 83 barg Continuous inlet pressure: 0.5–5 barg Peak inlet pressure: 5 barg Continuous speed: 700–1800 rpm Typical flow at 1000 rpm and maximum pressure: 4.62 m³/h Typical flow at 1500 rpm and maximum pressure: 6.93 m³/h Torque at maximum outlet pressure: 112 Nm Dry weight in 2024 data sheet: 30 kg Table motor-pump sound pressure, 1 m: 78 dB(A) Footprint with recommended IEC motor, excluding service: 0.35 m² Typical drive at maximum speed/pressure, not package scope: 22 kW Typical flow at 1200 rpm and maximum pressure, source unit: 24.39 gpm Typical flow at 1800 rpm and maximum pressure, source unit: 36.59 gpm Typical drive at additional tabulated duty, not package scope: 20 HP at 1200 rpm Inlet boost above 1500 rpm: 2–5 barg Execution duty: Seawater or brackish-water RO	A direct IMPA code is not confirmed
APP W 8.2 · 180B3078	Manufacturer article: 180B3078 Geometric displacement: 80.4 cm³/rev Minimum/maximum outlet pressure: 20 / 83 barg Continuous inlet pressure: 0.5–5 barg Peak inlet pressure: 5 barg Continuous speed: 700–1800 rpm Typical flow at 1000 rpm and maximum pressure: 4.62 m³/h Typical flow at 1500 rpm and maximum pressure: 6.93 m³/h Torque at maximum outlet pressure: 112 Nm Dry weight in 2024 data sheet: 30 kg Table motor-pump sound pressure, 1 m: 78 dB(A) Footprint with recommended IEC motor, excluding service: 0.35 m² Typical drive at maximum speed/pressure, not package scope: 22 kW Typical flow at 1200 rpm and maximum pressure, source unit: 24.39 gpm Typical flow at 1800 rpm and maximum pressure, source unit: 36.59 gpm Typical drive at additional tabulated duty, not package scope: 20 HP at 1200 rpm Inlet boost above 1500 rpm: 2–5 barg Execution duty: Conditioned wastewater; confirm fluid quality	A direct IMPA code is not confirmed

Selection and applicability

APP, APP W, APP S and ATEX articles are not interchangeable by name. Only the explicitly selected standard APP/APP W articles are shown. All barg values are gauge pressures. The 2024 dry mass is not the net/gross mass of a current article page; confirm revision and shipping mass before ordering. Tables state ambient 0–50 °C, section 8.1 states 2–50 °C; agree operation at 0–2 °C. Check fluid temperature and corrosion resistance against NaCl concentration. No exact IMPA code is confirmed for these additions.

Photographs and drawings

**Danfoss APP 5.1–10.2 — factory dimensional sheet**Dimensional sheet on page 29 of AI274333290009en-000702, revision 2024.06. The manufacturer states its size range on the sheet. This is the pump drawing, not a motor-pump assembly; agree the installation drawing for the supplied execution.

**Danfoss APP 8.2 — article 180B3008 photo**Manufacturer product-page photograph for article 180B3008, checked 6 Nov 2026. A catalogue representation, not an individual unit offered for supply; the photo does not establish a datasheet revision or package scope.

Include with your enquiry

Fluid, temperature, viscosity and solids
Flow and pressure at the duty point; operating cycle
Materials, seals, threads and available power or compressed air

Related sections

Request an offer

The specification, documents and supply terms are agreed for your enquiry. Supplier stock, lead time and price are confirmed in a separate offer.

Open selection and send an enquiry Contacts